Monster list-good stuff here

Last list for awhile. Located in Oran, Missouri, 63771. For pics or info you can PM me here, e-mail tilley88@att.net , phone (573)262-8863 or (573)318-4689. You pay shipping or pickup here. Here we go-

(1) 1987 Chevy dually pickup, 350, 4-speed. Old workhorse is kinda rough, needs a little TLC. It runs and is driveable, will need a tune up. It belongs to my brother and he said $1500 on it OR possible trades.
(2) Lightweight flywheel/clutch setup, sbc, 2 pc rear seal-10,000 RPM flywheel, ACE 6-puck clutch disc, ACE pressure plate, total weight around 28 pounds. Comes with QM stock type hydraulic throwout bearing and braided line-$300
(3)Lightweight fabricated valve covers, aluminum, bbc, new-$100
(4) Muncie aluminum 4-speed, M20, 1969 code dates, in excellent shape-$500
(5) Poly fuel cell, 10 gallon rear sump with fittings-$40
(6) 355 sbc short block, cast crank, “O” rods with good bolts, crappy small dome pistons, needs a lot of work, block has small chip in bottom of one cylinder-$50
(7) Cragar Aerotech aluminum wheels, 4.75” bolt pattern, 16” x 9.5”, comes with locking lugnuts AND locking center caps, very nice low mileage wheels-$300
(8) BBC steel heads, 292 casting, stock size valves, fresh from the machine shop with new springs, retainers, studs, and guide plates. Setup for hydraulic cam. Nice heads for a restoration or upgrade-$500
(9) World Sportsman 2 steel heads, sbc-bought new castings, added all new valve train, ran ‘em 9 nights on a solid lift 383. Comp dual valve springs and 10 degree retainers/locks, Manley Pro flow 2.02/1.60 valves, studs and guide plates. These have 64cc chambers, 200cc runners, and are straight plug-$800
(10) Vortec heads, sbc- casting 906, have 2.02/1.60 valves, Comp dual valve springs, studs, guide plates. These have only been ran one night since all new valve train was installed. Along with the Vortec bolt holes for the intake and centerbolt valve covers, they have the old style intake bolt holes drilled and tapped, and are setup for perimeter valve covers-$500
(11) Smog pump eliminator kit, sbc-this kit is new, polished aluminum. Comes with the pulley, brackets, and spacers, no bolts, but you can use your old ones-$100
(12) Kirkey 16” aluminum circle track seat with 4 piece seat cover set, nice shape-$100
(13) (2) Aluminum crank pullies, sbc-these measure 5-5/8”-$25 each
(14) Aluminum water pump pulley, sbc-this measures 5-7/8”-$25
(15) (2) Afco steel 4-link birdcages, new-these have no liner, steel on steel-$100 for the pair
(16) BBC roller tip rocker arms, Comp 1.72, comes with nuts and balls, new-$100
(17) BBC hydraulic cam, new-Chet Herbert, 112 LC, 515/510 lift, 272/284 duration-$65
(18) BBC moly pushrods, new-Comp 7931/7941-$100
(19) BBC screw in studs and guide plates, used-$25
(20) BBC head bolts, stock-$10
(21) BBC chrome valve covers, Moroso, nice shape-$30
(22) BBC aluminum intake, Weiand 7506, dual plane, oval port, nice shape-$75
(23) BBC harmonic balancer cover, Proform brand, new, silver with timing marks, for 8” balancer-$25
(24) Circle track valve covers, sbc-black with tubes on drivers side-$10
(25) Brodix, intake, sbc-used one night, single plane HVSP-1, fits stock, Dart, Bowtie, etc-$200
(26) (2)Circle track tubular gas pedals-$10 each
(27) Circle track shifter, 2 handle, decent shape-$5
(28) (2) Leaf spring stands, aluminum, Afco-these act as lowering blocks and bolt around your housing-$30 for the pair
(29) Steel fan blade, circle track, 6 blade, 15”-$15
(30) Steel fan blade, circle track, 6 blade, 17”-$10
(31) Nylon fan blade, circle track, 6 blade, 15”-$10
(32) Aluminum and steel wheel spacers, ¼” to ¾” thick, 4.5, 4.74, and 5.00 bolt patterns-$5 to $10 each
(33) Tubular upper a-arm-offset, 9” with 6” centers(slotted)-$15
(34) Tubular upper a-arm-offset, 8” with 6” centers(slotted)- $15
(35) Tubular upper a-arm-straight, 9” with 6” centers(slotted)-$10
(36) Tubular upper a-arm-straight, 8” with 7.75” centers-$15
(37) Richardson right side headrest, black, bolt on-$10
(38) Aluminum carb spacer, 2” open hole 4150-$20
(39) Aluminum carb spacer, 1” open hole 4150-$5
(40) Phenolic carb adapter, Q’jet to 2bbl Holley, nice-$40
(41) Drag link and idler arm, almost new, ‘73-’77 Chevelle, Cutlass, Monte Carlo, etc-$30
(42) X-Factor pullbar with 4-link bushing, used one night. Comes with swedge tube and heims-$175
(43) Southwest Speed pullbar with progressive spring, used one night. Comes with swedge tube and heims-$150
(44) Stock rocker arms, sbc-get a grab bag here, 40 total-$10
(45) Aluminum roller rockers, sbc-Blumax brand, 1.5 ratio, 3/8 stud, hardly used, look new-$100
(46) Mallory Unilite distributor, sbc or bbc-nice shape-$100
(47) Mallory Comp 9000 distributor, coil, and ballast resistor, sbc or bbc-$100
(48) (2) sets of Manley head bolts with washers, sbc-$30 each set
(49) Carter hi-volume fuel pump, sbc-this is the race version with 8an and 10an fittings-$40
(50) CNC slave cylinder, pull type. Nice shape, will throw in CNC push type body with it-$25
(51) Comp moly pushrods, set of 16, sbc (4903)-$40
(52) Moly pushrods, set of 16, sbc-this is a mixed bag, all good, all .100 long-$25
(53) Aluminum wheel adapter, 4.75 to 5x5-$25
(54) Slider, Afco-for 10” springs, in nice shape-$25
(55) Slider, Speedway Motors-for 13” springs-$40
(56) Slider, Howe-for 13” springs-$30
(57) Slider, Viper (I think)-for 13” springs, needs taken apart and cleaned, possibly rebuilt-$15
(58) Spring-Afco 175x10x5 rear-$10
(59) (2) Springs-Afco 200x13x5 rears-$15 each
(60) Spring-SSS 800x5.5x9.5 front-$10
(61) Spring-SSS 900x5.5x9.5 front-$10
(62) Spring-Afco 750x5.5x9.5 front-$15
(63) Spring-Trucoil 750x5.5x9.5 front(new)-$30
(64) Spring-Afco 600x5.5x9.5 front(new)-$40
(65) Spring-Afco 700x5x9.5 $20
(66) Spring-Afco 800x5x9.5 front-$20
(67) Spring-Afco 850x5x9.5-$10
(68) Spring-Afc0 900x5x9.5-$10
(69) Shock-Bilstein small body, 7” stroke, 3535-$40
(70) Shock-Bilstein small body, 7” stroke, 4545-$40
(71) Shock, Bilstein small body, 7” stroke, 3060-$40
(72) Shock-Bilstein big body, 9” stroke, 1090-$40
(73) Shock-Bilstein big body, 9” stroke, 2050-$60
(74) Shocks- Bilstein, big body, 9” stroke, 3030-$50 each
(75) Shocks- Pro, big body, 9” stroke, 9600-$10 each
(76) Shocks- Afco, stock position front, 1020-$10 each
(77) Shock- Afco, stock position front, 1022-$10
(78) Shocks-Pro, stock position front, SS100-$10 each
(79) Stock “X” connecting rods, sbc, complete set-$25
(80) 9” Ford floater housing, 60” centered-no gear, hubs, or axles, bare with brackets. It is straight, but welds on brackets look bad-$50
(81) Ultradyne solid roller cam, sbc-296/311 duration, 600/664 lift, in good shape-$50
(82) Speedway Motors solid cam, sbc-285/295 duration, 543/561 lift, in good shape-$50

This item is USED

Trades NOT ACCEPTED

Item Location: ORAN, MO Get Directions To This City

This ad expired 3 days ago.